Fracture Strength and Failure Modes of Endodontically Treated Premolars Restored with Compact and Hollow Composite Posts Subjected to Cyclic Fatigue.

Physical and mechanical properties of continuous carbon or glass fiber reinforced endodontic posts are relevant to increase the retention and resistance of the tooth-restoration system. Hollow posts have been recently designed for delivering the luting cement through the post hole, thus enhancing the post-dentin interface by reducing the risk of air bubbles formation. Methods: Three type of endodontic posts, a carbon fiber hollow post, a glass fiber hollow post and a compact glass fiber post were investigated. Mechanical properties of these posts were assessed through bending tests. Teeth were subjected to fatigue cycling and the strength of restored teeth was detected through static tests. Failure modes were investigated through optical and scanning electron microscopy. Results show that composite posts increase the mechanical stability by more than 100% compared to premolars restored with particulate composite. Carbon fiber posts retain the highest strength (1467 N ± 304 N) among the investigated post and core restoration, but an unfavorable type of fracture has been observed, preventing the tooth re-treatment. Instead, more compliant posts (i.e., glass fiber reinforced composite, providing a strength of 1336 N ± 221 N), show a favorable mode of fracture that allows the re-treatment of teeth in the case that failure occurs. Glass fiber hollow posts show a good trade-off between strength and a favorable type of fracture.

The resin-matrix cement layer thickness resultant from the intracanal fitting of teeth root canal posts: an integrative review.

OBJECTIVE: The aim of this study was to perform an integrative review on the layer thickness and microstructure of resin-matrix cements around custom-made or standard teeth root intracanal posts. MATERIALS AND METHODS: An electronic search was conducted on the PubMed using a combination of the following scientific terms: intraradicular post, root intracanal post, resin cement, thickness, adaptation, endodontic post, layer thickness, fit, shape, and endodontic core. The literature selection criteria accepted articles published in the English language, up to May 2021, involving in vitro analyses, meta-analyses, randomized controlled trials, and prospective cohort studies. RESULTS: The search identified 154 studies, of which 24 were considered relevant to this study. The selected studies provided important data considering cement layer thickness, tooth preparation, endodontic post, and type of resin-matrix cement. The anatomical variability of root canal systems, such as the oval- or C-shaped, represents a challenge in dental restoration with tooth root intracanal posts. The fitting of intracanal posts to different root regions is variable resulting in thick and irregular layers of resin-matrix cement. Defects like pores, micro-cracks, and micro-gaps were detected in the resin-matrix cement microstructure and represent spots of stress concentration and fracture. Custom-made tooth root intracanal posts provide a proper fitting and decrease the layer thickness of resin-matrix cement. CONCLUSIONS: In fact, the layer thickness of resin-matrix cements depends on the fitting of endodontic posts to tooth root canals. An increase of resin cement thickness causes the appearance of defects like pores, micro-cracks, and micro-gaps that can induce stress concentration and fractures at interfaces. CLINICAL RELEVANCE: The fitting of the endodontic post into the teeth root canal determine the layer thickness of the resin-matrix cement to establish an adequate retention. However, the increase in the thickness of the resin-matrix cement layer can lead to a high number of defects like pores or cracks and therefore decrease the strength of the interface.

Effect of MTA versus CEM apical plugs on fracture resistance of endodontically treated simulated immature teeth restored with cast metal posts: an in-vitro study.

BACKGROUND: Endodontically treated immature teeth which are restored with cast metal posts are of the most susceptible teeth to fracture. An apical plug is usually used as root end filling in order to seal the wide apical foramen. The current study was performed to evaluate the effect of different apical plug materials (MTA and Calcium enriched mixture cement) at varied thicknesses on fracture resistance of teeth restored with cast metal posts. METHODS: A total of 40 extracted intact single-rooted human mandibular premolars (removed for orthodontic reasons) were used in the study. The coronal part of each tooth was removed and root canal preparation was performed. A size 4 Gates Glidden drill was used to enlarge the canal and was passed through the apical foramen in order to simulate an immature apex. Samples were randomly divided into 5 groups (n = 8) according to apical plug (control group: No plug, group MTA5: 5 mm MTA plug, group CEM5: 5 mm CEM plug, group MTA3: 3 mm MTA plug, group CEM3: 3 mm CEM plug). Post-space preparations were performed and cast metal post-and-cores were fabricated and cemented. Fracture resistance was assessed using a universal testing machine. Fracture thresholds were recorded and data were analyzed using One-way ANOVA and Dunnett's T3 tests with significance level at P value < 0.05. RESULTS: The analysis showed a significant difference of fracture resistance between groups (P value < 0.05). The mean fracture resistance of samples in control group was significantly lower than MTA5 (P value = 0.003). There was no significant difference between other groups (P value > 0.05). CONCLUSIONS: Within the limits of this study, the evidence indicated that placement of a 5 mm MTA apical plug increased the fracture resistance in simulated immature teeth which are restored with cast metal posts, compared to control group (gutta-percha and sealer). While the results were not as promising for a 3 mm MTA apical plug or either 3 or 5 mm CEM apical plug.

Mechanical and thermal stress evaluation of PEEK prefabricated post with different head design in endodontically treated tooth: 3D-finite element analysis.

An endodontic post is required to retain and support the core restoration in case of insufficient remaining coronal dentin after root canal therapy. This study analyzed the biomechanical and thermal behavior of PEEK prefabricated post after choosing the head design that produces the least amount of stress on the core and remaining tooth structure. These results were compared with the most common commercially available prefabricated post, which is titanium and glass fiber post. Thus a CBCT scanning of a maxillary central incisor with its supporting structure was used to construct a 3D solid model of an endodontically treated teeth for finite element analysis (FEA). The restored tooth with the spherical head design of PEEK prefabricated post yielded a more benign stress distribution and repairable failure mode on the crown, luting cement, core, and dentin under both mechanical and thermal loads, followed by glass fiber post and titanium post respectively.

Fracture resistance of endodontically treated teeth restored with various esthetic posts.

BACKGROUND: Dental esthetic materials are constantly introduced to meet the increasing esthetic demand in contemporary dental practice. OBJECTIVE: To test the fracture resistance of endodontically treated teeth (ETT) restored with different esthetic post materials like fiber-reinforced composite post (FRC), polyether ether ketone (PEEK), and polymer infiltrated ceramic (PIC). METHODS: Thirty-six human root canal treated single-rooted premolar teeth were decoronated 3 mm above the cemento-enamel junction and prepared to receive the post. They were randomly divided into three groups (n= 12) to be restored with FRC, PEEK, and PIC. After appropriate surface treatment, they were cemented with self-adhesive luting cement and restored with full veneer crowns. The samples were thermocycled, subjected to a compressive static load at 45∘ angulation until fracture. Obtained data were analyzed by one-way ANOVA and Tukey's HSD post hoc comparison test. RESULTS: The results indicate that the ETT restored with PEEK post had the maximum fracture load (1929.94 N), followed by PIC endodontic post group (1810.65N), and FRC post (1715.68N). Meanwhile, ETT restored with FRC showed a predominantly favorable fracture, whereas PEEK restored teeth had a more unfavorable fracture. CONCLUSION: Of all the esthetic post materials, the group for which PEEK endodontic post was used displayed higher fracture resistance.

Stress Distributions for Hybrid Composite Endodontic Post Designs with and without a Ferrule: FEA Study.

The aim of the current work was to analyze the influence of the ferrule effect for hybrid composite endodontic post designs consisting of carbon (C) and glass (G) fiber-reinforced polyetherimide (PEI), in upper canine teeth. Starting from theoretical designs of C-G/PEI hybrid composite posts with different Young's moduli (Post A-57.7 GPa, Post B-31.6 GPa, Post C-graduated from 57.7 to 9.0 GPa in the coronal-apical direction) in endodontically treated anterior teeth, the influence of the ferrule effect was determined through finite element analysis (FEA). On the surface of the crown, a load of 50 N was applied at 45° to the longitudinal axis of the tooth. Maximum principal stresses were evaluated along the C-G/PEI post as well as at the interface between the surrounding tooth structure and the post. Maximum stress values were lower than those obtained for the corresponding models without a ferrule. The presence of a ferrule led to a marked decrease of stress and gradients especially for posts A and B. A less marked effect was globally found for Post C, except in a cervical margin section along a specific direction, where a significant decrease of the stress was probably due to local geometric features, compared to the model without a ferrule. The presence of a ferrule did not generally provide a marked benefit in the case of the graduated Post C, in comparison to other C-G/PEI posts. The outcomes suggest how such a hybrid composite post alone should be sufficient to optimize the stress distribution, dissipating stress from the coronal to the apical end.

When to install the endodontic post? First visit with root canal filling versus a separate second visit for post-restoration: A randomized controlled trial.

BACKGROUND: The vibrations created by post-space preparation during the first visit for endodontic treatment could have a significant effect on the intensity of post-operative pain than that association with post-space preparation at the second appointment. OBJECTIVE: The aim of this study was to evaluate the effect of vibrations generated during post-installation, on post-operative pain in endodontically treated teeth. METHODS: One hundred patients with asymptomatic teeth requiring primary root canal treatment and post-installation were enrolled in this study. Fifty patients underwent endodontic treatment with post-installation at the first visit (group 1), while the remaining 50 patients underwent post-installation at the second visit (group 2). The intensity of post-operative pain in both groups was evaluated 1, 2, 3 days and 1 week after the first visit using the visual analogue scale. The time required to achieve complete pain relief for each patient was also recorded. The patients' age, sex, tooth type, size of the periapical lesion and time required for complete post-operative pain relief for each tooth were recorded. RESULTS: The pain intensity score was significantly higher in group 1 than group 2 (P < .05). No significant differences were observed in parameters such as sex, tooth type, jaw and size of the periapical lesion (P > .05), whereas age had a significant effect on the post-operative pain scores (P < .05). CONCLUSION: Vibrations occurring during post-installation on the same visit as that of root canal filling may increase the post-operative pain.

Evaluation of Mechanical Properties of a Hollow Endodontic Post by Three Point Test and SEM Analysis: A Pilot Study.

The aim of this study was to investigate the mechanical properties of a fiber hollow endodontic post characterized by the presence of an empty central cylindrical channel extended along the whole length. This particular shape allows clinicians to use the post also as a cementation resin carrier. Ten hollow posts were divided in two groups: the control group (unfilled hollow posts) (Group 0) and hollow posts filled with dual resin cement (Group 1). The samples of both groups were subjected to mechanical and micromorphological analysis by performing a three-point test and SEM observations. In the three-point test, the Group 1 samples exhibited a fracture load of 57.09 ± 5.06 N, a flexural strength of 1323.53 ± 110.09 MPa, and a Young's modulus of 42.87 ± 0.86 GPa. The samples of Group 2 exhibited a fracture load of 38.17 ± 1.7 N, a flexural strength of 908.87 ± 30.98 MPa, and a Young's modulus of 40.33 ± 1.9 GPa. The difference between fracture load, flexural strength, and deflection between the two groups was statistically highly significant (p < 0.01). Further, the difference between the Young's modulus of the two groups was statistically significant (p < 0.05). The values obtained are similar to those of other posts available on the market.

Patients' self-report on post-retained restoration is more valuable than expected! Explorative analysis of an 11-year follow-up.

Objective: Assessment of long-term clinical data regarding post-endodontic restorations is essential for the evaluation of different post-and-core concepts. The aim of the present study was to assess the diagnostic accuracy of patient self-reporting on post-endodontic restorations after 11 years of clinical service.Materials and methods: Twenty-nine patients (61 ± 15 years old) with endodontic glass-fibre and titanium post-endodontic restorations were examined within the 11-year follow-up of a randomized controlled trial. Restorations were assessed by self-reports during a telephone interview (one item), the completion of a four-item questionnaire and clinical and radiographic examination. A gold standard for restoration in situ or 'failure' was defined by clinical and radiographic examination. Diagnostic accuracy of patients' self-reports was evaluated by calculating the sensitivity, specificity, and positive (PPV) and negative predictive values (NPV).Results: After a mean observation time of 137 months (min/max: 125/154 months), 25 (86.2%) restorations were in situ and 4 (13.8%) failures were detected. Self-report during a telephone interview and the four-item questionnaire correctly identified all in situ restorations (specificity = both 100%, NPV = 92.6%/96.2%). Self-report during a telephone interview identified two out of four failures (sensitivity = 50%, PPV = 100%), and self-report on the four-item questionnaire identified three out of four failures (sensitivity = 75%, PPV = 100%).Conclusions: When the clinical examination is not feasible, patients' self-report shows valuable diagnostic potential in the identification of the post-endodontic failure.

Direct restoration of endodontically treated maxillary central incisors: post or no post at all?

OBJECTIVES: The aim of this ex-vivo study was to evaluate the impact of cavity size and glass-fiber post (GFP) placement on the load capability of endodontically treated maxillary incisors directly restored with resin composite. MATERIALS AND METHODS: Ninety-six extracted human maxillary central incisors were endodontically treated and distributed to four groups (n = 24): access cavity (A), access cavity and uni-proximal class III cavity (U), access cavity and bi-proximal class III cavity (B), and decoronated tooth (D). Specimens were restored with resin composite, and 12 specimen of each group received an adhesively placed glass-fiber post (P). Prior to linear loading, specimens were exposed to thermo-mechanical loading (TCML). Statistical analysis was performed using log-rank test after TCML, Kruskall-Wallis and Mann-Whitney U test to compare load capabilities (Fmax). RESULTS: Significantly more failures occurred in group D for specimens without GFP during TCML (p = 0.001). Fmax (mean (SD) in N was (A) 513 (124), (AP) 554 (201), (U) 438 (171), (UP) 537 (232) (B) 483 (219), (BP) 536 (281), D 143 (181), and DP 500 (331), and differed significantly among groups (p = 0.003). Pair-wise comparison revealed lower Fmax values for group D compared to all other groups (p < 0.034) except group DP. CONCLUSIONS: Endodontically treated maxillary central incisors with cavity sizes up to bi-proximal class III may be successfully directly restored with resin composite. Post placement shows no additional effect except for decoronated endodontically treated incisors. CLINICAL RELEVANCE: Endodontically treated incisors with access cavities to class III cavities can be successfully restored with resin composite. Post placement for decoronated ETT is recommended.

Cimentação adesiva dos retentores de fibra de vidro: o que precisamos saber? / Adhesive cementation of fiber posts: what we need to know?

Este artigo descreveu, através de uma revisão da literatura, conceitos atuais acerca da cimentação adesiva de pinos de fibra de vidro. Já que a união entre cimento resinoso, pino e dentina assume um papel importante na longevidade do tratamento protético restaurador. Na presente revisão, foram discutidos tópicos como a influência da espessura do cimento, as estratégias adesivas que podem ser utilizadas e fatores que podem influenciar na escolha do tipo de cimento resinoso a ser utilizado, os métodos indicados para a inserção desses cimentos no interior do conduto radicular e os conceitos referentes ao tratamento de superfície, tanto do pino de fibra como da superfície dentinária.

This paper has described through current literature concepts the adhesive cementation of fiberglass posts since the adhesive union between resin cement, post and dentin plays an important role in the longevity of the restorative and prosthetic treatment. The present review discussed topics such as: the influence of cement thickness, the adhesive strategies that can be used and factors that may influence the choice of the type of resin cement to be used, the methods indicated for the insertion of these cements inside the root canal, and concepts regarding the surface treatment of both post and dentin surfaces.

The Post-endodontic Adhesive Interface: Theoretical Perspectives and Potential Flaws.

INTRODUCTION: The aim of this review was to analyze the potential of successful bonds of endodontic posts to radicular dentin as well as the limitations of the post-endodontic adhesive interface. METHODS: The MEDLINE/PubMed and Web of Science electronic databases were searched. The search was augmented by a manual search of the pertinent bibliographies. RESULTS: The post-endodontic adhesive interface finds application in the endodontic cohesive units. Many techniques and materials exist to improve the bond between endodontic posts and resin-based materials as well as between resin-based materials and radicular dentin. Different techniques used for the adhesion of metallic and fiber-reinforced posts are discussed and critically analyzed. CONCLUSIONS: Although adhesive cementation of endodontic posts is popular, a long-term predictable bond may be compromised because of procedures related to the endodontic treatment and/or the adhesive cementation procedures. Microleakage and degradation phenomena may further jeopardize the post-endodontic adhesive interface.

Dentin-like versus Rigid Endodontic Post: 11-year Randomized Controlled Pilot Trial on No-wall to 2-wall Defects.

INTRODUCTION: This is the first long-term randomized controlled trial to evaluate dentin-like glass fiber posts (GFPs) compared with rather rigid titanium posts (TPs) for post-endodontic restoration of severely damaged endodontically treated teeth with 2 or fewer remaining cavity walls. METHODS: Ninety-one subjects in need of post-endodontic restorations were randomly assigned to receive either a tapered GFP (n = 45) or TP (n = 46). Posts were adhesively luted by using self-adhesive resin cement, followed by composite core build-up and preparation of 2-mm ferrule design. Primary end point was loss of restoration for any reason. Kaplan-Meier curves were constructed, and log-rank test was calculated (P < .05). RESULTS: After a follow-up of 132 months, 17 GFP and 20 TP restorations survived, and 19 failed (12 GFP, 7 TP). Failure modes for GFP were root fracture (n = 4), core fracture (n = 1), secondary caries (n = 1), endodontic failure (n = 2), extraction because of tooth mobility grade III associated with insufficient design of removable partial denture (n = 1), tooth fracture (n = 1), and changes in treatment plan (n = 2); failure modes for TP were endodontic failure (n = 5), root fracture (n = 1), and 1 extraction for other reasons. Cumulative survival probability was 58.7% for GFP and 74.2% for TP. CONCLUSIONS: When using self-adhesively luted prefabricated posts, resin composite core build-up, and 2-mm ferrule to reconstruct severely damaged endodontically treated teeth, tooth survival is not influenced by post rigidity. Survival decreased rapidly after 8 years of observation in both groups.

Influence of irrigating agents on fiber postpush-out bond strength to radicular dentin sections with the different adhesive system.

OBJECTIVE: The objective of this study is to evaluate the effect of irrigating agents on push-out bond strength of resin postcemented with various adhesive systems at different radicular dentin sections. MATERIALS AND METHODS: Sixty single-rooted premolar teeth were root canal treated, subsequently decorated at cementoenamel junction. The endodontic postspace was irrigated with 5.25% sodium hypochlorite (NaOCl) and 17% ethylenediaminetetraacetic acid (EDTA) for Group A (n = 30) and Group B (n = 30), respectively. The sample from each group was subdivided into three groups (10) according to luting protocol of etch-wash, self-etch, and self-adhesive. Individual teeth with cemented resin postsamples were sectioned into coronal, middle, and apical segments. Subsequently, subjected for pushout bond strength test by applying a load at 0.5 mm/min speed. The data were analyzed by three-way analysis of variance and Tukey comparison test at a significant difference level of 0.05. RESULTS: The coronal section with 5.25% NaOCl irrigation and self-etch luting protocol provided the highest push out strength at 16.282 Mpa. The etch-wash luting protocol in both irrigations showed the lesser bond strength at 8.273 and 8.493 MPa, respectively, in coronal section. CONCLUSIONS: The self-etch adhesive system showed better push out bond strength and 17% EDTA had a negative influence on self-etch bond strength. The coronal sections had highest bond strength in comparison with apical radicular dentin sections.

Fracture Strength of Flared Root Canals Restored with Different Post Systems.

OBJECTIVE: To evaluate the fracture resistance of different intra-radicular post systems in flared root canals. METHODS: Sixty human canines were used. The coronal portion was removed and the root length was standardized at 17 mm. Canals were prepared and filled with gutta-percha/AH Plus sealer. Roots were embedded in self-polymerising acrylic resin blocks. According to the material used, the teeth were randomly divided into three groups (n=20): glass fibre post (GFP): GFP and Z350 resin composite core; pre-fabricated metal post (PMP): PMP and Z350 resin composite core; and cast metal core (CMC): CMC with silver-tin alloy. Coronal reconstruction involved fabrication of metal copings. Samples were submitted to mechanical compression testing at 45º in a universal test machine. Fracture pattern was evaluated under a stereoscope. The fracture strength values were submitted to one-way analysis of variance (ANOVA) and Tukey tests (α=0.05). RESULTS: There was no statistically significant difference between the resistance values among groups (P=0.193). With regard to fracture pattern, GFP showed 55% and PMP 45% of Type I fractures, which considered repairable or favourable, whereas MCC presented 50% of Type V, which was considered irreparable or unfavourable. CONCLUSION: Glass fibre and pre-fabricated metal posts have good fracture resistance to compression and may be used for restoring flared root canals, since they presented fractures mainly involving the filling core, thus facilitating later repair.

Influence of a polymerizable eugenol derivative on the antibacterial activity and wettability of a resin composite for intracanal post cementation and core build-up restoration.

OBJECTIVES: Eugenol has been used in dentistry due to its ability to inhibit the growth of a range of microorganisms, including facultative anaerobes commonly isolated from infected root canals. The aim of this study was to evaluate the antibacterial activity of the experimental composites containing eugenyl methacrylate monomer (EgMA), a polymeric derivative of eugenol, against a range of oral bacteria, commonly associated with failure of coronal and endodontic restorations. In vitro composite behavior and wettability were also studied in conjunction with their antibacterial activity. METHODS: EgMA monomer (5 and 10% by weight) was added into BisGMA/TEGDMA resin based formulations with filler mixtures of hydroxyapatite (HA) and zirconium oxide ZrO2. The antibacterial activity of the experimental composites against Enterococcus faecalis, Streptococcus mutans and Propionibacterium acnes were evaluated by direct contact test and compared with composite formulation without inclusion of EgMA. To clarify the antibacterial mode of action, agar diffusion test (ADT) was also performed. Water sorption, solubility, diffusion coefficient, contact angle and surface free energy as complementary clinically relevant properties were determined. RESULTS: Water sorption and wettability studies showed reduction of water uptake and surface free energy values with increasing content of EgMA monomer, resulting in significant increase in the hydrophobicity of the composites. No inhibition zones were detected in any of the composites tested against the three bacteria employed as expected, due to the absence of any leachable antibacterial agent. The covalently anchored EgMA monomer with the composite surface exhibited an effective bacteriostatic activity by reducing the number of CFUs of the three species of bacteria tested with no significant dependence on the concentration of EgMA at 5 and 10% by weight. The surface antibacterial activity R of the experimental composites were different against the three tested species with values in the range 2.7-6.1 following the order E. faecalis

A resin composite material containing an eugenol derivative for intracanal post cementation and core build-up restoration.

OBJECTIVES: To formulate and evaluate new dual cured resin composite based on the inclusion of eugenyl methacrylate monomer (EgMA) with Bis-GMA/TEGDMA resin systems for intracanal post cementation and core build-up restoration of endodontically treated teeth. METHODS: EgMA was synthesized and incorporated at 5% (BTEg5) or 10% (BTEg10) into dual-cure formulations. Curing properties, viscosity, Tg, radiopacity, static and dynamic mechanical properties of the composites were determined and compared with Clearfil™DC Core-Plus, a commercial dual-cure, two-component composite. Statistical analysis of the data was performed with ANOVA and the Tukey's post-hoc test. RESULTS: The experimental composites were successfully prepared, which exhibited excellent curing depths of 4.9, 4.7 and 4.2 mm for BTEg0, BTEg5 and BTEg10 respectively, which were significantly higher than Clearfil™DC. However, the inclusion of EgMA initially led to a lower degree of cure, which increased when measured at 24 h with values comparable to formulations without EgMA, indicating post-curing. The inclusion of EgMA also lowered the polymerization exotherm thereby reducing the potential of thermal damage to host tissue. Both thermal and viscoelastic analyses confirmed the ability of the monomer to reduce the stiffness of the composites by forming a branched network. The compressive strength of BTEg5 was significantly higher than the control whilst flexural strength increased significantly from 95.9 to 114.8 MPa (BTEg5) and 121.9 MPa (BTEg10). Radiopacity of the composites was equivalent to ∼3 mm Al allowing efficient diagnosis. SIGNIFICANCE: The incorporation of EgMA within polymerizable formulations provides a novel approach to prepare reinforced resin composite material for intracanal post cementation and core build-up and the potential to impart antibacterial properties of eugenol to endodontic restorations.

Evaluación in vitro de filtración hacia conducto radicular de dos sistemas de reconstrucción post endodóncica / In vitro assessment of root canal leakage of two post-endodontic reconstruction systems

El objetivo de este estudio fue el de evaluar el grado de microfiltración en dos sistemas de reconstrucción postendodóncica, valorando la penetración de un colorante a lo largo de las restauraciones realizadas con endopostes y cementos duales de resina. En este estudio se emplearon 30 dientes premolares unirradiculares extraídos a los que se les realizó tratamiento de conductos y almacenándolos en agua bidestilada a 37 ºC. Se distribuyeron los dientes en tres grupos de forma aleatoria, con diez dientes por cada grupo. La cementación de los postes se realizó en dos de los grupos, usando los sistemas RelyX Fiber post (3M ESPE dental products) y Parapost (Coltene-Whaledent). Las muestras fueron sometidas al proceso de termociclado y posterior inmersión en azul de metileno por siete días a 36 ºC. Posteriormente se diafanizaron las muestras y fueron analizadas bajo microscopio, obteniendo los valores de penetración en milímetros. Los resultados mostraron que los dientes tratados con el sistema Parapost presentaron menor microfiltración. El grupo control mostró el mayor índice de microfiltración. El análisis estadístico con la prueba de Donett mostró diferencia estadísticamente significativa entre los sistemas Parapost y RelyX. Conclusión: Se demostró que el sistema de reconstrucción Parapost (Coltene-Whaledent), el cual tiene una técnica de grabado ácido, reportó menores valores de microfiltración, siendo los resultados estadísticamente significativos con respecto a los obtenidos con el sistema de reconstrucción RelyX (3M ESPE dental products).

The aim of the present study was to assess the degree of microleakage observed when using two different post-endodontic reconstruction systems; this was achieved assessing penetration of a dye along restorations performed with endodontic posts and dual-cure resin cements. For the present study, 30 extracted, single rooted premolars were used. Root canal treatment was performed on the teeth which were later stored in bi-distilled water at 37 ºC. Teeth were randomly allotted to three groups, all groups were comprised of 10 teeth. In two groups, post cementation was performed using the systems RelyX Fiber Post (3M ESPE dental products) and Parapost (Coltene-Whaledent). Samples were subjected to thermo-cycling and later immersed in methylene blue for seven days at 36 ºC. After this, samples were subjected to a diaphanization process and were then analyzed under a microscope; penetration in millimeters was thus obtained. Results revealed that teeth treated with Parapost system exhibited lesser microleakage. Control group experienced the greater amounts of microleakage. Statistical analysis conducted with Donett test showed statistically significant difference between Parapost and RelyX systems. Conclusion: Parapost reconstruction system (Coltene-Whaledent) with acid-etch technique exhibited lower microleakage values. Results were statistically significant when compared to those obtained with the RelyX reconstruction system (3M ESPE dental products).

Stress distributions in maxillary central incisors restored with various types of post materials and designs.

Different dental post designs and materials affect the stability of restoration of a tooth. This study aimed to analyse and compare the stability of two shapes of dental posts (parallel-sided and tapered) made of five different materials (titanium, zirconia, carbon fibre and glass fibre) by investigating their stress transfer through the finite element (FE) method. Ten three-dimensional (3D) FE models of a maxillary central incisor restored with two different designs and five different materials were constructed. An oblique loading of 100 N was applied to each 3D model. Analyses along the centre of the post, the crown-cement/core and the post-cement/dentine interfaces were computed, and the means were calculated. One-way ANOVAs followed by post hoc tests were used to evaluate the effectiveness of the post materials and designs (p=0.05). For post designs, the tapered posts introduced significantly higher stress compared with the parallel-sided post (p<0.05), especially along the centre of the post. Of the materials, the highest level of stress was found for stainless steel, followed by zirconia, titanium, glass fibre and carbon fibre posts (p<0.05). The carbon and glass fibre posts reduced the stress distribution at the middle and apical part of the posts compared with the stainless steel, zirconia and titanium posts. The opposite results were observed at the crown-cement/core interface.

Comparison of stresses induced by fiber post, parapost and casting post in root canals by photoelasticity method.

INTRODUCTION: Many studies have been performed to evaluate the stress distribution around endodontic posts; those which compared posts composed of different materials are rare. The aim of this study was to compare stresses induced in dentin by three structurally different posts using photoelasticity method. MATERIALS AND METHODS: Nine blocks of PSM-5 Photoelastic material with 45×45×10 mm dimension were prepared. In each block, a canal 9 mm in length and 0.8 mm in width was drilled. Blocks were divided into 3 groups of three each. In the first group, the canals were prepared for insertion of Fiber Post with 1.25 mm width. In the second group, the canals were prepared for insertion of ParaPost with 1.25 mm width and the canals in the third group were prepared for casting post similar to the above samples. Casting Post pattern was made by Duralay resin and casted by Ni-Cr alloy. All posts were cemented in canals with Panavia cement. The stresses were evaluated in the polariscope under three different conditions: 1) without load, 2) with 135 N vertical load, and 3) with 90 N oblique load (26° inclination to post long axis). The fringe orders in the cervical, middle and apical regions of the posts were evaluated and compared with each other. RESULTS: Application of the vertical load induced a high stress concentration (FO=4) in the apical region of the ParaPost, while lower stress was observed in the middle (FO=2) and cervical region (FO=2+). Fiber Post and Casting Post showed even stress distribution (FO=2+). High stress concentration was detected with the application of oblique force in the cervical region of ParaPost (FO=5) and Casting Post (FO=3+). Fiber Posts fractured before reaching 90-N loading force. CONCLUSION: The stress distribution around Fiber Post and Casting Post were constant in comparison with ParaPost. Fiber Post with 1.25 mm width was not recommended in situations with high oblique stresses.